Bedienungsanleitung Multiplex Power Peak D7 EQ-BID - 30 8129 (Seite 26 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

Select Order of the process

Charge

(for Li-xx bat-

teries)

The process is switched off if all the cell volta-

gesareadequatelybalanced,thedefined"TVC

voltage" is reached, and the charge current has

fallen to 10%. This is a charge process which

rapidly charges the battery, with a good com-

promise between cell balance and charged-in

capacity. The capacity charged in is higher than

that obtained with a "fast charge".

Charge

(for NiCd /

NiMH batte-

ries)

Battery is charged using the set charge para-

meters. Process terminates according to the

Delta-Peak method.

Automatic

(NiCd / NiMH

batteries only)

In "AUTOMATIC" mode the charger automa-

tically sets the optimum charge current. The

maximum charge current is defined by the

"Charge current" parameter in the "Memory

name" menu.

Discharge

In "Discharge" mode the battery is discharged

using the current defined in the "Discharge

current" parameter in the "Memory name" menu

(max. 40 W). The final discharge voltage is

defined by the "Discharge voltage" parameter.

Re-peak

(NiCd / NiMH

batteries only)

In "RE-PEAK" mode it is possible to define the

number of re-peaks (1 ... 3) using the "RE-PEAK"

parameter in the Mode Select menu. With old

NiCd / NiMH batteries, or packs which have

been in storage, this ensures that they really are

fully charged at the end of the charge process

(i.e. the mode compensates for early charge

termination). The defined number of "re-peaks"

is worked through in sequence. After every peak

the charger automatically waits for five minutes.

After this pause the next charge process starts,

and this continues until all "re-peaks" and the

"normal peak" have been completed.

Cycle

(NiCd / NiMH

batteries only)

In "CYCLE" mode a battery is alternately char-

ged, then discharged; or discharged, then char-

ged. This is designed to compensate for the

Memory Effect, allowing your battery to be used

again at full capacity.

Between the individual charge / discharge pro-

cesses a pause is inserted; the length of the

pausecanbeadjustedinthe"Pausetime"para-

meter in the "User settings" menu.

Storage

(Li-xx batteries

only)

The charger can bring Li-xx batteries to the

following voltages prior to storage (e.g. over the

Winter):LiPo: 3.8 V/C,LiIo: 3.7 V/C,LiFe: 3.3

V/C.Sincethebatterymayneedtobecharged

or discharged to achieve this, both the charge

current and the discharge current must be set

beforehand. Recommendation:

Use every six weeks when batteries are not in

use.

Fast charge

(Li-xx batteries

only)

The process is switched off if all the cell voltages

areadequatelybalanced,andthedefined"TVC

voltage" (in the "Memory name" menu) is rea-

ched. The charge current is not reduced. This is

a charge process which charges the battery very

rapidly, with a good compromise between cell

balance, charged-in capacity and charge time.

Balance

(Li-xx batteries

only)

The process is switched off if all the cell voltages

are adequately balanced, the defined "TVC

voltage" is reached (in the "Memory name"

menu), and the charge current has fallen to

10%. This is a charge process which produces

very well-balanced cells and optimum charged-

in capacity.

When you have set the mode, navigate to "CYCLE" and hold the

"START / ENT." button pressed in. The process begins, using the

mode you have selected.

Note:

Thepausebetweencyclescanbeadjustedinthe"Usersettings"

menu (see P. 10).

The following table explains the individual user selection options:

When used with NiCd and NiMH batteries, the Power Peak

EQ-BID switches over to a trickle (maintenance) charge at the end

of the main charge process.

TheCC-CVchargeprocessconsistsofthreephases,andisused

for the following battery types: LiFe, LiIo, LiPo and Pb

1. In the CC (Constant Current) Phase the charge current is maintai-

ned at a constant level until the final charge voltage is reached.

2.ThisphaseisfollowedbytheCV(ConstantVoltage)phase,in

which the voltage is maintained at a constant level. The battery is

nowalreadychargedtoapproximately85-90%offullcapacity,

and the charge current is reduced further.

3.When98%capacityisreached(chargecurrent=capacity/10)

the cut-off melody sounds and the cut-off display appears on the

charger's screen. In practical terms the battery is fully charged,

and can be disconnected from the charger.

CC phase

Constant Current

CVphase

ConstantVoltage

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak D7 EQ-BID - 30 8129 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info