Bedienungsanleitung Multiplex Power Peak D7 EQ-BID - 30 8129 (Seite 27 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

13. STARTING A CHARGE / DISCHARGE PROCESS

Before the programmed process is started, the battery must be con-

nected to Output 1 or 2 with correct polarity (see chapter 5.2). Use

the appropriate charge lead from the comprehensive robbe range.

The process is actually started by pressing the "START / ENT." but-

ton: you will hear a confirmation beep. This means that the charger

is checking the battery connected to it; the screen informs you of

this.

If no battery is connected, you will see an on-screen warning of the

error, and hear a warning beep.

Note:Lithiumbatteriesmust alwaysbecharged withtheVoltage

Sensor lead connected.

Charge LiPo

Charge

Checking battery

Waiting. . .

14. SCREEN DISPLAYS DURING A PROCESS

14.1 SCREEN DISPLAYS DURING CHARGE / DISCHARGE

AND CYCLE PROCESSES

Once the process has started, the screen changes to the working

display, which shows all the important values relating to the cur-

rent process. The illustration below shows the working display for

a LiPo battery charge process. The working display is divided into

two screens.

Pressing the "START / ENT." button takes you to a display of the

voltage curve. If you are charging a Lithium battery, pressing the

"START / ENT." button a second time takes you to the Equalizer

display. Press the "START / ENT." button once more to return.

The displayed value for internal resistance is automatically calcu-

lated by the Power Peak

D7 EQ-BID.

Note:

It is possible to alter the current during a charge / discharge

process: navigate to the "CURRENT" function by pressing the

"START / ENT." button, then change the current using the "+" or

"-" buttons. The new value applies only to the current process, and

is not saved.

During a cycle process the working display also looks similar. The

screen displays "CYCLE" while the battery is being checked. The

illustration shows the upper part of the screen display during a

cycle, in this case while a battery is being charged.

When the charger is connected to the mains, i.e. the internal PSU

is in use as power supply, the "Input voltage" parameter shows a

valueof17.4V.

In addition to all the current process parameters, the screen dis-

plays the mode, the current phase and the cycle sequence. During

each phase the corresponding symbol flashes (D = Discharge, C

= Charge).

Cycle NiMH

Cycle  : D>C

Time : 00.00.46

Capacity : 38mAh

Voltage : 5.77V

Current : 1.00 A

In.Volt : 11.78V

BATT. Res : 350 mO

Charge LiPo

Time : 00.00.46

Capacity : 19 mAh

Voltage : 11.54V

Current : 1.95 A

In.Volt : 11.78V

Batt.Res : 48mO

Int. temp. : 35°C

12. CONNECTING A BATTERY

Important!!! Before connecting a battery pack, check one

last time that all the set parameters are correct! If the settings are

incorrect, the battery may be damaged, explode, or catch fire. To

avoid short-circuits between the banana plugs, always connect the

charge leads to the battery charger first, and only then to the battery.

Take care to maintain correct polarity!

Reverse the sequence when disconnecting.

Connecting the equalizer:

The black wire of the voltage sensor lead attached to the Lithium

battery must be connected to the charger at the arrow marking. The

arrow indicates the negative terminal. Take care to maintain correct

polarity!

This example is only intended as a general guide; it shows how to

connect the voltage sensor lead to the equalizer.

Note:

It is essential to connect the battery voltage sensor lead to the

charger before charging or discharging a Lithium battery. This

is a safety requirement!

Do not connect the outputs in parallel, and never connect the

positive and negative terminals together. Neglecting this war-

ning will result in damage to the charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak D7 EQ-BID - 30 8129 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info