Bedienungsanleitung Cambridge Audio Azur 751R V2 (Seite 35 von 40) (Englisch)

656755

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

751R V2azur

ENGLISH

DTS-HD speaker re-map

As there is no "ofcial" speaker layout for discrete 7.1 channel audio it

could be possible that the original master track of a 7.1 soundtrack was

mastered with a different speaker layout than the one being used in your

home. DTS have addressed this issue for DTS-HD Master Audio and High

Resolution Audio by including in the bitstream ags to tell the receiving

AV Receiver which of a 7 nominal 7.1 speaker layouts was actually used.

By using special DTS Speaker Remap algorithms the 751R V2 is able to

electronically "reposition" the speakers (i.e. direct the audio propagation), so

that the playback matches the original encoded layout for the best possible

sound quality.

A second aim of this technology is that by re-purposing some of the 7.1

available channels it is possible to use some of them to do new things such

as adding a height element to the sound eld.

The following digrams show the 7 possible encoding schemes for reference.

The angles quoted refer to the angle from a nominal 0 degrees line through

the centre channel to each speaker either side right or left of that line.

Congurations 1 and 5 are variants of normal 7.1 setups whilst Conguration

6 can increase the available panning of the front channels.

Congurations 2, 3, 4 and 7 are less conventional and re-purpose some of

the available 7.1 channels to provide an extra height dimension to the sound

eld in different ways. Conguration 4 is the one the 751R V2 expects if you

choose to use a 5.1 + Height speaker setup. Please refer to the DTS website

for more details on this new technology.

Conguration 1 – 7.1 channel: L, C, R, LFE, Lss, Rss, Lsr, Rsr

Center

Right (30°)

Left (30°)

Left Surround Side (90°)

Left Surround Rear (150°)

Right Surround Rear (150°)

Right Surround Side (90°)

LFE

Conguration 2 – 7.1 channel: L, C, R, LFE, Ls, Rs, Lhs, Rhs

Center

Right (30°)

Left (30°)

Left Height Side (90°)

Left Surround (110°)

Right Surround (110°)

Right Height Side (90°)

LFE

Conguration 3 – 7.1 channel: L, C, R, LFE, Ls, Rs, Cs, Oh

Center

Center Surround

Right (30°)

Left (30°)

Left Surround (110°)

Right Surround (110°)

LFE

Center Over-Head

To turn off Zone 2 simple press Zone 2 followed by the Standby/Off button

again.

To select Tuner in Zone 2, press Zone 2 followed by the Tuner button.

Do this again to switch from AM to FM or vice versa.

To select other sources in Zone 2 press Zone 2 followed by the desired

source button.

To select the same source as the main room's, press Follow Main.

To change the volume is Zone 2 press Zone 2 followed by the volume up or

down buttons (or volume knob).

To mute Zone 2 press Zone 2 followed by the Mute button.

You can also use the Zone 2 handset in the main room to control Zone 2.

In this case all the remote commands automatically control Zone 2, simply

point the Zone 2 handset at the main unit and use the Standby/On or source

buttons to always control Zone 2 operation.

Note: The Zone 2 handset has a couple of special features.

Using the

or preset up down buttons for the Tuner will always

automatically put the tuner into Preset mode (as opposed to Manual or

Automatic modes).

Note: The Tuner will also only scroll through Presets that have actually been

set.

The Zone 2 remote has a Follow Main function. This forces Zone 2 to follow

the same source selection as the main zone. This can be useful in that Zone

2 can now receive any audio type including digital or HDMI audio that is

being decoded for the main zone. The Zone 2 outputs are created from Left

+ Centre and Right + Centre so that centre channel dialogue can be heard

in Zone 2.

It is also possible to control Zone 2 via the On Screen Display.

From the main OSD screen select the Rec.2/Zone 2 Output Select menu and

then select the Zone 2 menu item.

azur 751R Main Menu

Speaker Setup

HDMI/Component Assign

Video Input Select

Scaler Assign

Video Processing Settings

Audio Input Select

Tone/Sub/LFE Config.

Rec.2/Zone2 Output Select

Advanced Setup

Quit I/O

Use the ◄ and ► buttons on the remote scroll to through the various

sources available, Follow Main and Off.

Controlling Zone 2 from Zone 2 itself

As previously described you will need an IR repeater system in order to do

this.

This allows commands received in Zone 2 to be relayed back to the Zone 2

IR Emitter Input on the back of the unit.

Via such a repeater you can use both the main and Zone 2 handsets in Zone

2. For both handsets all commands received will automatically affect Zone 2.

I.e. for the main zone handset when used in this way in Zone 2 you do not

need to press Zone 2 followed by another command. Simply select a source

or mute etc. and the unit will automatically do that function in Zone 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 751R V2 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 751R V2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info